Comments on: D-Link Voip Products – Review 1

By: ab

ab — Wed, 03 Nov 2010 14:44:24 +0000

I have solved my own problem and in the end it was mad simple by my master, the Holy Spirit.
Steps to use the DVG-6004s with 3CX Server

1. Reset the DVG to its default setting
2. connect to the WAN port and join it to your LAN
3. Set up a trunk port on the 3CX (making a note of the parameter)
4. Create an appropriate outgoing rule on the 3CX
5. On the SIP tab of the DVG-6004s. set up the FXO representative number with the parameter from the 3CX box. leave the FXO tabs at the default setting
6. On the telephony tab, enable FXO port where you have your PSTN line connected and chech the hotline tab. Put in the value of your trunk line from the 3CX set up.

There you are,you can start enjoying your DVG-60004 device.

Regards
Abiodun

By: ab

ab — Mon, 18 Oct 2010 16:32:42 +0000

Thanks to the author for the article and to all for their contributions.

Will: i am currently setting up the DVG with 3CX box and i am glad to say that i was able to register it has a trunk.

The challenge is that i cannot coerce it to allow PSTN calls at times it gives the busy signal and at other times it rings but not on the called PSTN numbers.

Any thought on what i am doing wrong? Thanks to your anticipated help

Cheers
Abiodun

By: Luciano Carvalho

Luciano Carvalho — Fri, 14 May 2010 22:11:02 +0000

More than 2 years ago, I made some attempts to use DVG-6004S efficiently with Asterisk (the first comment on this post is mine). Now I’m back to say that in the last 3 months I’m using DVG with a firmware upgrade togueter with 3CX pbx software. I’ve been able to configure it as a trunk with all the benefits included, like using all 4 FXO ports individually on my dialplan. Also CID is being properly delivered to the SIP clients. Maybe you should give a new try to DVG-6004S / Asterisk with the new firmware!

By: will

will — Fri, 27 Jun 2008 07:40:25 +0000

thanks a lot~ I have registered the DVG-6004S as a sip user in asterisk server and also I typed the command: sip show peers, I can see the DVG-6004S as a sip user in the server also I can make phone call from PSTN network to IP network. So from above all, I think I have registered the DVG-6004S successfully in the asterisk server. But I still can not make the phone call from IP network to PSTN network. Do you think it is something wrong with extension.conf file? We added your command: exten = s,1,Dial(SIP/701,20,gtTwWmD(ww${ARG1:1})) in extension.conf, but still can not. Could you please figure out the problems for us?

By: Lor

Lor — Fri, 13 Jun 2008 08:17:59 +0000

I didn’t configure mgcp.conf. I had DVG-6004S as a client to Asterisk server.

There is no need to configure zapata.conf as zaptel cards are not used.

Make sure you have DVG-6004S registered as client to Asterisk. You can use Asterisk command prompt to check that this is done correctly. Then it should work for outgoing as per my description above.

I am sorry that I may not be able to help further because I had DVG-6004S on loan. I have since returned it.

By: will

will — Fri, 13 Jun 2008 06:48:18 +0000

Thanks for your reply first. Do you think I should make some change in mgcp.conf and zapata.conf both or just configure sip.conf and extension.conf. Because I still can not make phone calls to pstn network by following your explainations.

By: Lor

Lor — Thu, 12 Jun 2008 14:38:24 +0000

The section under “Making outgoing call to PSTN via DVG-6004S” in the article explains that.

By: will

will — Thu, 12 Jun 2008 03:25:09 +0000

I have some questions on making outgoing call to pstn. Could you pls tell me more detials about how to write the dial-plan on asterisk server and configuration on dvg-6004s? now i can only make calls from pstn to sip phone. thanks

By: Shrenik Bhura

Shrenik Bhura — Wed, 04 Jun 2008 02:52:34 +0000

It is possible to use DVG-6004S as a SIP trunk and I have done it before but unfortunately I am unable to replicate the same settings again. Will post again if I get success.

By: Lor

Lor — Thu, 24 Jan 2008 03:01:34 +0000

Thanks.

I don’t think you can use DVG-6004S as a SIP trunk. It has to be a SIP client to Asterisk. So, it is best to use it the way as I described.

As for the CID of incoming calls, I am sorry to say I have no success. This despite seeking much help from D-Link. They said it is possible, gave me some configurations that just do not work.